. Room Air Conditioners Bravo Inverter Range Split Type DC Inverter ECO916SD ECO1216SD ECO1816SD ECO2416SD Register your air conditioner Model information can be found on the CE label. Please register your product online at www.ecoair.org. For your future convenience, record the model information below. WARNING: Before operating your unit WARNING Make sure the wiring is adequate for your unit. Before you install or relocate this unit, be sure that the amperage rating of Electrical Shock Hazard the circuit breaker complies with the amp rating listed in Figure 1. Always consult a qualified electrician regarding the power supply to the appliance.
BS Plug Wiring (For models up to 12000 Btu) Wiring Instructions: Should it be necessary to change the plug please note the wires in the mains lead are coloured in accordance with the following code: BLUE - NEUTRAL BROWN – LIVE GREEN AND YELLOW - EARTH As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. Congratulations! You have purchased the very latest in room air conditioner technology.
Wiring Instructions: Should it be necessary to change the plug please note the wires in. EcoAir high efficiency room air conditioner will give you many years of.
Your new EcoAir high efficiency room air conditioner will give you many years of dependable service. Many features have been built into your EcoAir air conditioner to assure quiet operation, the best circulation of cool, dry air, functional controls, and the most economical operation. Operation and maintenance-notices for operation ★ ★ ★ Earth: The ground Be sure to remove the power Select the most appropriate tem- be connected!
Plug when not using the air co- perature. Nditioner for a long time.
Keep room cool- er than outside about 5 degree. Notices for operation ★ ★ The airflow direction can be adjusted appro- If the supply cord is damaged, it must be replaced priately. At operating, adjust the vertical airflow by the manufacturer or its service agent or a direction by adjusting the louvers of upward/do- similarly qualified person in order to avoid a wnward direction. Notices for use Working principle and special functions for cooling Principle: The air conditioner transfers heat from the indoor area to the outdoor area, thus reducing the indoor room temperature, using heat pump technology. Anti-freezing function: In COOL mode under low ambient temperature, frost will form on the heat exchanger. When the indoor heat exchanger temperature decreases to below 0℃, the indoor unit microcomputer will stop the compressor from running.
Notices for use Working temperature range Indoor side DB/WB( Outdoor side DB/WB( Maximum cooling 32/23 48/ - 21/15 Minimum cooling 10/- Maximum heating 27/- 24/18 Minimum heating 20/- -15/- The operating temperature range (outdoor temperature) for cooling unit is 21℃ 43℃；. Names and functions of each part Indoor unit Air in ⑴ ⑶ ⑺ ⑹ ⑸ ⑷ Air out ⑵ Wireless (1) Power cable remote control Cool (2) Remote Control Heat Power (3) Front panel (4)Filter ON/OFF Receive window (5)Guide louver Outdoor unit (6)Wall pipe Air in. Operation of remote control Names and functions of remote control buttons Note: Ensure there is no obstruction between the indoor unit and the remote control; Don't drop or throw the remote control; Don't spill any liquid onto remote control. Do not put the remote control directly under the sunlight or heated areas.
Operation of remote control Names and functions of remote control buttons NOTE: This remote control may have some buttons that are not available to your model. TIMER AUTO Timer button OPER HEALTH X-FAN ● Whilst unit is on, you may press this HUMIDITY FILTER button to set timer off.
Operation of remote control Guide for operation-general operation 1.Press ON/OFF button to start the unit after powering the main unit on.(Note: The big -guide louver and small-guide louver will close automatically during ON/OFF MODE Power on). 2.Press MODE button to select desired running mode. 3.Press +/ - button to set the desired temperature (You cannot set the temperature in AUTO mode, it is preset) 4. Operation of remote control ★ About AUTO RUN When AUTO RUN mode is selected, the setting temperature will not be displayed on the LCD, the unit will be in accordance with the room temp. Automatically to select the suitable running method and to make ambient comfortable. Emergency operation Display indicator light control of indoor unit It's a special selective button for the users, who are not accustomed to the light at sleeping.
● Get the display indicator light on: When setting the light function, the mark will display on the remote controller screen by pressing this button. Clean and care Caution Turn power off and pull out the power plug before cleaning air conditioner, or it may cause ● electric shock. Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an ●.
Clean and care Check before use ① Be sure that nothing obstructs the air outlet and intake vents. ② Check that ground wire is properly connected or not. (Important) ③ Check that the batteries of the remote control changed if remote is not working. Troubleshooting CAUTION Don't attempt to repair the air conditioner by yourself, it can cause an electric shock or fire. Please check the following items before asking for repair, it can save your time and money. Problem Troubleshooting Not operate immediately when the air ●. Troubleshooting Troubleshooting Problem The unit is not.
Has the power been shut down?. Is power connected properly?.
Is the circuit protection device tripped off or not?. Is voltage higher or lower? (Tested by professionals).
Eco R410a Portable Air Conditioner Manual
Is the TIMER correctly used? Breaking off. Troubleshooting Problem Troubleshooting No air delivery from indoor unit. ● In HEAT mode, when the indoor temperature is very low, air delivery will be delayed for up to 5 minutes.
● In HEAT mode, when the outdoor temperature is low or high humidity, frost may form on the outdoor heat exchanger. Notices for installation Important Notices Installation work must be done by competent or qualified persons according to local rules and this manual. All electric supply to the unit must be carried out by qualified electrician. Reinstallation of the unit must be carried out by qualified persons. The appliance must be positioned so that the power supply is accessible. Notices for installation Outdoor Unit Installation Position Selection Select a location from which noise and outflow air emitted by unit will not be a nuisance to neighbours, animals or plants. Select a location where there should be sufficient ventilation.
Select a location where there should be no obstructions to the inlet and outlet vent. The location should be level and able to withstand the full weight and vibration of the outdoor unit and permit safe installation. Installation dimension diagram Installation dimension diagram Space to the ceiling Above Space to the wall Above Above Space to the wall Above Above Air outlet side Space to the floor The dimensions of the space necessary for correct ● installation of the appliance including the minimum permissible distances to adjacent structures Space to the obstruction Air inlet side. Install indoor unit Install the rear panel 1.Always mount the rear panel horizontally. The outlet of water tray should be adjusted slightly downward when installing to enable gravity flow of condensation externally. 2.Fix the rear panel on the wall with screws. (Where is pre-covered with plastic granula) 3.Be sure that the rear panel has been fixed firmly enough to withstand the weight of an.
Install indoor unit NOTE: Where the electric cable length is not long enough, replace with another that is long enough as joints on the cables are not to be avoided. Ensure the replacement cable is of the same quality and diameter.
The electric wiring must be correctly connected, wrong connection may cause spare ●. Install outdoor unit Electric wiring Disassemble the handle on the outdoor unit right side plate. Take off cord anchorage.
Connect and fix power connect cord (for cooling and heating unit, connect and fix power connect cord and signal control wire)to terminal block. Fix the power connection cable with cord anchorage, (for cooling and heating unit, use the cord anchorage to fix the power. Check after installation and test operation Check after installation Items to be checked Possible malfunction Has it been fixed firmly? The unit may drop, shake or emit noise. It may cause insufficient cooling(heating) Have you done the refrigerant leakage test? Capacity It may cause condensation and dripping.
Installation and Maintenance of Healthy Filter Installation Instructions 1. Forcibly pull the panel for a specific angle from the two ends of the front panel according to the arrow direction.
Then pull the air filter downwards to remove it. ONE (1) YEAR LIMITED WARRANTY SAVE THIS WARRANTY INFORMATION EcoAir guarantees this product free from defects in materials and workmanship for a period of one (1) year from the date of purchase, limited to parts only. Faults arising from a faulty installation is specifically excluded.
Eco Temp Air Conditioning
This unit must be operated under conditions as recommended, at voltages indicated on the unit.